astm c33 chloride content limits


Grading of Fine Aggregate with ASTM-C33 (2003) limits ...

Download Table | Grading of Fine Aggregate with ASTM-C33 (2003) limits from publication: Impact of Cement Replacement Partially by Mosaic powder on Compressive Strength of Concrete | Mosaic tile ...

Get More

§501 Section 500 PORTLAND CEMENT CONCRETE

ASTM C33 Size Number 7 is an acceptable equivalent to the Type CA 1 gradation. ASTM C33 Size Number 57 is an acceptable equivalent to the Type CA 2 gradation. Material passing the 75 µm sieve (wet) is limited to a maximum 1.0 % by mass for ASTM sizes 7 and 57. 2. Friction.

Get More

Introduction and Background - PennDOT

Limit to 1% of Mixture Deleterious Materials ASTM C40, ASTM 295, ASTM C142 ASTM D2419 ... (ASTM C131, ASTM C33, AASHTO T96681, ASTM C535) is used to - ... • Chloride Content specifically looks at chloride ion entrainment from RPCC aggregates. Chloride

Get More

Evaluation of Chloride Limits for Reinforced Concrete Phase A

content is less than the specified limit, there is good assurance that the water-soluble chloride measured on hardened concrete will comply and this testing may be avoided. Alternatively, if a ... • ASTM C33 No. 57 crushed coarse aggregate with high chloride from Illinois (IL) • ASTM C33 …

Get More

(PDF) Designation: C33/C33M − 16 Standard Specification ...

Originally For referenced ASTM standards, visit the ASTM website,, or approved in 1921. Last previous edition approved in 2013 as C33/C33M – 13. DOI: contact ASTM Customer Service at [email protected]

Get More

Criteria for Freeze-Thaw Resistant Concrete Mixtures

• ASTM C33/C33M-16 [17] No. Fifty-seven crushed coarse aggregate; • ASTM C33 [17] natural sand with an FM¼2.88; • ASTM C260/C260M-10a [18] Air-Entraining admixture, blend of saponified rosin and organic salts; • ASTM C494/C494M-15a [19] Type F, polycarboxylate based. Concrete mixtures were proportioned to obtain an air content from 5 ...

Get More

ASTM C33 / C33M - 18 Standard Specification for Concrete ...

2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.. ASTM Standards. C29/C29M Test Method for Bulk Density (Unit Weight) and Voids in Aggregate. C40/C40M Test Method for Organic Impurities in Fine Aggregates for Concrete. C87/C87M Test Method for Effect of Organic Impurities in Fine ...

Get More

CONCRETE 1.1 Summary

ASTM C231 - Test Method for Air Content of Freshly Mixed Concrete by the Pressure Method. UPDATED 11/13/2008 LHC 03300-3 ... Conform to ASTM C33 (1) Limits for deleterious substances and physical ... chloride ions added during manufacture. d. Storage

Get More

Standard Specification for Concrete Aggregates1

6 Annual Book of ASTM Standards, Vol 04.03. 7 Annual Book of ASTM Standards, Vol 14.02. TABLE 1 Limits for Deleterious Substances in Fine Aggregate for Concrete Item Mass Percent of Total Sample, max Clay lumps and friable particles 3.0 Material finer than 75-µm (No. 200) sieve: Concrete subject to abrasion 3.0A All other concrete 5.0A Coal ...

Get More

Chloride limits in the ACI 318 building code requirements

The test for acid-soluble chlorides (ASTM C 1152) treats crushed material with nitric acid rather than water. Almost all of the chlorides present in the concrete are detected, whether they are bound or are available to cause corro-sion. Because the test method finds all chlorides, limits based upon acid-soluble chloride content are higher than

Get More

Analysis of total chloride content in concrete - ScienceDirect

It can be seen in Fig. 1 that the BS 8500 (BS 8500-1, 2006) total chloride limit for reinforced concrete that is non-heat curing and made with sulphate resistance cement (0.2) is nearly violated at mix M4 (w/c = 0.48) even though the chloride content is less than BS 882 (BS 882, 1992) standardized limits for aggregate and ASTM C 94 (ASTM C 94 ...

Get More

ASTM C33 / C33M - 18 Standard Specification for Concrete ...

Scope. 1.1 This specification defines the requirements for grading and quality of fine and coarse aggregate (other than lightweight or heavyweight aggregate) for use in concrete. 2. 1.2 This specification is for use by a contractor, concrete supplier, or other purchaser as part of the purchase document describing the material to be furnished.

Get More

Aggregates for Use In Concrete

Source: Table 1 Limits for Deleterious Substances in Fine Aggregate for Concrete, ASTM C 33. * In the case of manufactured sand, if the material finer than the 75-micron (No. 200) sieve consists of the dust or fracture, essentially free of clay or shale, these limits are permitted to …

Get More

State Building Code: Pyrrhotite in Concrete Aggregate

national standard that incorporates ASTM C33, which is an industry standard for concrete ... 3 Plasticity limits T 90 0 or not detectable 4 L.A. Abrasion T 96 50% maximum (fine agg. particle size ≥ No. 8 ... Chloride content must be determined in accordance with AASHTO T 260, Procedure A. Regardless of chloride content, reclaimed aggregates ...

Get More

Chloride content limits recommended by ACI Committee 201

tests for total chloride content (of the hardened concrete) be made first, according to the method of ASTM C 114. (If desired, the chlori d e content of any of the ingre d i e n t s may be determined separa t e l y.) If the total chloride content exc e e d s the allowable limits, then the water-soluble portion should be mea-s u re d .

Get More

Section 500 RIGID PAVEMENTS

Sieve Sizes Type CA 1 General Limits % PassingType CA 2 General Limits% Passing 37.5 mm -- 100 25 mm 100 93-100 12.5 mm 90-100 27-58 25 6.3 mm 0-15 0-8 NOTE: Coarse aggregate meeting the gradation requirement for ASTM C33 coarse aggregate size number 7 are acceptable alternates to the Type CA 1 gradation.

Get More

Recommended limits for aggegates - SlideShare

TABLE – ( 1 ) Recommended limits for the Physical and mechanical properties of aggregates Property (and standard which Method of test (and standard Recommended maximum limit (%by describes it) which describes it) weight) Grading Sieve analysis Ranges of sizes in table (4) (BS 882) (Bs 812) shell content Bs 812-106 Max. 10% of fine aggregate ...

Get More